about_this_syncswap_information_website_and_editorial_scope [Japanese Woodworking Wiki]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.


img  width: 750px;  iframe.movie  width: 750px; height: 450px; 
Syncswap multichain dex wallet setup and trading walkthrough



Syncswap Multichain DEX Wallet Setup and Trading Instructions

Install a browser extension like MetaMask or Rabby. During creation, meticulously record your 12-word secret recovery phrase on paper; store this offline. Fund your new interface with ETH from a centralized service to cover network fees.

Connecting to a Layer 2 Network

Access your extension's network settings. Manually input the following details for zkSync Era:


Network Name: zkSync Era Mainnet
RPC URL: https://mainnet.era.zksync.io
Chain ID: 324
Currency Symbol: ETH
Block Explorer: https://explorer.zksync.io


Confirm and switch to this network. Your interface is now configured for a low-fee environment.

Acquiring Initial Assets

Navigate to a bridge portal like Orbiter Finance or Rhino.fi. Lock your mainnet ETH to mint a representation on zkSync Era. This process typically requires 5-10 minutes for confirmation.

Configuring the Swap Interface

Visit the application's website. Select "Connect" and authorize your extension. The interface will display your zkSync Era ETH balance. Before your first exchange, you must permit the router to access your tokens. This approval is a one-time gas fee per asset.

Executing an Asset Exchange

Locate the swap panel. Choose ETH from the "From" dropdown. Select USDC for the "To" asset. Input an amount, for instance, 0.1 ETH. The interface shows an estimated output, inclusive of a 0.3% liquidity provider fee and the current price impact. A 0.5% slippage tolerance is usually sufficient for stable pairs. Confirm the transaction in your pop-up extension; verify the gas fee. The swap finalizes in one block, roughly 5 seconds.


For limit orders, select the "Limit" tab. Specify you will sell 1 ETH when its price reaches 3,200 USDC. This order rests on-chain until execution or cancellation.

Providing Liquidity

Select the "Pool" section. Choose to create a new pool for two assets, like ETH and USDC. Deposit a 50/50 value ratio. You will receive LP tokens representing your share. Note that impermanent loss affects volatile pairs.


Monitor positions through your connected portfolio dashboard. Withdrawals return to zkSync Era; use a bridge to move funds back to Ethereum mainnet, which can take 24+ hours for security finalization.

Syncswap Multichain DEX Wallet Setup and Trading Walkthrough

Install a browser extension like MetaMask or Rabby, fund it with ETH on Ethereum mainnet, then bridge assets to zkSync Era using the platform's native bridge for minimal fees.


Connect your funded portfolio to the interface, select a liquidity pool matching your asset pair–check projected APRs and volume. Input your swap amount, review the estimated output including the 0.3% fee, and confirm the transaction directly in your extension. Monitor the swap confirmation on the blockchain explorer; for adding liquidity, deposit an equal value of both tokens into your chosen pool to receive LP tokens representing your share.

Q&A:
Is my existing Ethereum wallet like MetaMask compatible with Syncswap, or do I need a new one?

Yes, you can use your existing Ethereum wallet. [[https://sync-swap.com/about.php|SyncSwap Web3 trading]] is built on zkSync Era, an Ethereum Layer 2 network. Wallets like MetaMask, which support custom networks, work perfectly. You don't create a new wallet within Syncswap; you connect your existing one. The setup involves adding the zkSync Era network to your wallet if it's not already there. This usually requires entering the correct RPC details, which the Syncswap interface typically provides or guides you to find. Once your wallet is connected to the zkSync Era network, you can connect it to the Syncswap dApp to begin.

What's the actual step-by-step process to get funds onto Syncswap for trading?

First, ensure your wallet (e.g., MetaMask) is connected to the Ethereum mainnet and has ETH. Then, go to the Syncswap interface and find the "Bridge" section. You will select Ethereum as your source chain and zkSync Era as the destination. Enter the amount of ETH you want to transfer and confirm the transaction in your wallet. This bridge process moves your ETH from Ethereum L1 to zkSync Era L2. It takes several minutes and incurs a gas fee on the Ethereum network. After the bridge completes, your wallet balance on zkSync Era will update. These funds are now ready for trading on Syncswap.

How does swapping tokens on Syncswap differ from a centralized exchange like Binance?

The core difference is control and process. On Binance, you deposit funds into an account controlled by the company, and trades happen on their internal systems. On Syncswap, you never give up custody of your assets; they remain in your connected wallet. A swap is a direct, peer-to-contract transaction. You approve the dApp to spend a specific token, then execute a swap transaction. The trade is processed by smart contracts on zkSync Era, with liquidity provided by other users. This means you need to manage network fees (gas) on zkSync and understand transaction confirmations. It's less about account balances and more about direct blockchain interactions.





After trading, how do I get my tokens back to the Ethereum mainnet?

To move assets back, you use the bridge in reverse. In the bridge section of Syncswap or the official zkSync portal, select zkSync Era as the source chain and Ethereum as the destination. Choose the token and amount you wish to withdraw. Initiating this withdrawal requires a transaction on zkSync Era. There is a delay, often around 24 hours for zkSync Era, as the process involves a security finalization period. After this delay, you must complete the withdrawal by finalizing it on the Ethereum mainnet, which requires another transaction and pays an Ethereum gas fee. Your assets will then be back in your wallet on Ethereum L1.

I'm trying to use Syncswap on a chain other than Ethereum mainnet. I've added the network to my MetaMask, but my funds still aren't showing. What step did I miss?

You likely missed the step of adding the specific bridge-wrapped token contract to your wallet. Simply having the network active isn't enough. Each chain on Syncswap uses its own version of tokens (like USDC.e or USDT). After bridging assets to the new chain (e.g., Arbitrum or zkSync), you must manually import the token contract address for your funds to be visible in MetaMask. Find the correct token address for your destination chain using a block explorer or Syncswap's own interface. Go to your MetaMask asset list, click "Import tokens," paste the address, and the balance should appear. Then, Syncswap will recognize it for trading.